Categories
6CH 2.4GHz Radiolink Transmitter & Receiver LCD Prog T6EHP & R6EH

Move to view larger images

6CH 2.4GHz Radiolink Transmitter & Receiver LCD Prog T6EHP & R6EH 6CH 2.4GHz Radiolink Transmitter & Receiver LCD Prog T6EHP & R6EH

6CH 2.4GHz Radiolink Transmitter & Receiver LCD Prog T6EHP & R6EH 6CH 2.4GHz Radiolink Transmitter & Receiver LCD Prog T6EHP & R6EH

6CH 2.4GHz Radiolink Transmitter & Receiver LCD Prog T6EHP & R6EH 6CH 2.4GHz Radiolink Transmitter & Receiver LCD Prog T6EHP & R6EH

6CH 2.4GHz Radiolink Transmitter & Receiver LCD Prog T6EHP & R6EH

Price: $65.57
SKU: 59408
464
diggs
Price in points: 656 points
Points: 6 points
Out Of Stock

Our wholesale prices:

Quantity  5+   20+   50+   100+ 
Price  $65.57   $65.57   $65.57   $65.57 
Description

6CH 2.4GHz Radiolink Transmitter & Receiver LCD Prog T6EHP & R6EH

This Radiolink product is digital proportional R/C helicopter system. If this is your first “computer” radio. Rest assured that it is designed to make initial setup and field-tuning of your helicopter easier and more accurate than would be if using a “non-computer” radio. Although this is a beginner or sport system with the requirements of those flyers in mind in order to make the best use of your Radiolink T6EHP-E and to operate it safely, you must carefully read all of the instructions .Suggestion :if ,while reading the instructions ,you are unclear of some of the procedures or functions and become “stuck ”,continue to read on anyway. Often ,the function or  procedure will be explained again  later in a different way providing another perspective from which to understand it. Another suggestion is to connect the battery ,switch  and servos to the receiver and actually operate the radio on your workbench as you male programming changes. Then, you will be able to see the effects of your programming inputs.

Throttle hold switch- This switch operates to hold the engine in the idling position and disengaged it from the Throttle stick. It is commonly use to practice auto- rotation.
 
Neck strap hook- Mounting point for optional neck strap.

Aileron / Throttle control stick- Operates the servos connected to channel 1 ( aileron ) and channel 2 ( throttle ) in the receiver.

Trim levers ( all ) – Used to shaft the neutral or center position of each servo.

Note: The throttle trim lever is intended for fine turning the throttle servo when the engine is at idle. Throttle trim dose not affect the throttle servo when the throttle control stick is all the way up ( so idle r. p. m. can be adjusted without affecting throttle settings through the rest of the stick movement )

DATA INPUT Button- Used to change the values of the various functions displayed on the LCD screen

Liquid – crystal display screen (LCD) – Displays programming modes and values entered .MODE key – Used to display the values for the current function.

SELECT Button – Used to display the values for the current function.

Throttle / Rudder control stick – Operates the servos corrected to channel 3 ( throttle )and channel 4 (rudder) in the receiver.

Idle up (Gyro) switch –This switch operates to change the flight condition which is set the throttle Curve and pitch of mid air maneuvers ( rolls, loops stall turns) and 3D flight. When you change the Idle up switch, the gyro sense will be changed to Idle setting too. So you don’t need to operate 2 switch (Idle up and Gyro sense switches ) while you want to change to 3D flying situation.

Antenna-Radiates signals to the receiver, Never fly a model without fully extending the antenna or you may create interference to other modelers and decrease operational signal range of the transmitter. The antenna may be removed and replaced with another in case it is inadvertently broken.

CONTENTS AND SPRCIFICATION


Transmitter:T6EHP
- T6EHPE Transmitter with 6-model memory.
- Transmitting on 2.4GHz band
- Operating system:2-stick,6-channel system
- Modulation: FHSS
- Power supply :9.6v Ni- Cd  battery or 12v alkaline battery
- Current drain:60mA

Receiver:R6EH
- R6F narrow band,2.4GHz 6 channel receiver
- Receiver requirement:4.8v -6v
- Current drain:9.5mA@4.8v

Package Contents
- 1 x 6 Channel 2.4G Transmitter
- 1 x 6 Channel 2.4G Receiver 

Previous: PS2 Quality Waterproof Gaming Keyboard for Laptop PC

NextCar Headrest Head-rest TFT LCD Monitor 7" Screen

Customer Images

Reviews
Write a ReviewPost PhotosPost Videos, and get GoodLuckBuy points!
  6CH 2.4GHz Radiolink Transmitter & Receiver LCD Prog T6EHP & R6EH
Posted by Paulo Andre on 08/26/2010, 00:56
Involvement:Novice (still getting used to it) - Ownership:1 day to 1 week
Price: ****
Ease of Use: *****
Build Quality: *****
Usefulness: ****
Overall Rating: ****
Pros:Product of excellent quality, functional and easy handling, recommended to all this radio control.
Cons:Manual could be translated into other languages
Other Thoughts:Product arrived within days and the deadline.
Bottomline:I was really pleased with the product.

Discussions

Loading...
122