Categories
CNC Kit 3 Axis NEMA 23 Stepper Motor 76MM *3+ TB6560 Driver Controller

Move to view larger images

CNC Kit 3 Axis NEMA 23 Stepper Motor 76MM *3+ TB6560 Driver Controller CNC Kit 3 Axis NEMA 23 Stepper Motor 76MM *3+ TB6560 Driver Controller

CNC Kit 3 Axis NEMA 23 Stepper Motor 76MM *3+ TB6560 Driver Controller CNC Kit 3 Axis NEMA 23 Stepper Motor 76MM *3+ TB6560 Driver Controller

CNC Kit 3 Axis NEMA 23 Stepper Motor 76MM *3+ TB6560 Driver Controller CNC Kit 3 Axis NEMA 23 Stepper Motor 76MM *3+ TB6560 Driver Controller

CNC Kit 3 Axis NEMA 23 Stepper Motor 76MM *3+ TB6560 Driver Controller

CNC Kit 3 Axis NEMA 23 Stepper Motor 76MM *3+ TB6560 Driver Controller

Price: $147.54
SKU: 64933
477
diggs
Price in points: 1475 points
Points: 14 points

Our wholesale prices:

Quantity  5+   20+   50+   100+ 
Price  $147.54   $147.54   $147.54   $147.54 
Description
Features of TB6560 Driver:
  • Toshiba TB6560AHQ chip - High power, maximum 3.5A drive current chipset !
  • 1-1/16 microstep setting - Higher accuracy and smoother operation than standard 1, 1/2 step!
  • Adjustable 1.5A-3A drive current settings for each axis - 25%,50%,75%,100% of full current can be set for different stepper motors
    *Attention: This driver is the 1.5A-3A version, it's specially designed for stepper motors with rated current from 1.5A to 3A, it's NOT compatible with stepper motors with rated current below 1.5A or above 3A!
    If the rated current your stepper motors is below 1.5A, you can choose the 0.5A-2.5A version!
    Please let us know which version (1.5A-3A version is default) you need immediately after placing a bid!
  • Overload, over-current and over-temperature safety - Full protection for your computer and peripheral equipment !
  • On board current switching - Power output can be set according to specific user requirement !
  • Full closed-type optical isolation to protect the user's computer and equipment
  • Relay spindle interface - Outputs Max. 36V 7.5A for spindle motors or coolant pump (only one device can be powered by this output!)
  • 4 channel inputs interface- Can be used for XYZ limit and emergency stop !
  • Professional design - Two stage signal processing with super anti-jamming !
  • Bipolar constant current chopper drive with non-resonant region - Controls motors smoothly through range without creep effect !
  • Four control inputs (divided into pairs of knives) - Allows setting of limit and emergency stop !
  • Universal architecture - Supports most parallel software MACH3,KCAM4 etc!
    *For compatibility with other softwares, please feel free to contact us!
Dip settings  of TB6560 Driver:
Current Setting 1 2 Decay Mode Settings 3 4 MicroStep Settings 5 6
100% ON ON FAST ON ON 1 ON ON
75% ON OFF 25% ON OFF 1/2 ON OFF
50% OFF ON 50% OFF ON 1/8 OFF ON
25% OFF OFF SLOW OFF OFF 1/16 OFF OFF

Further Details of TB6560 Driver:

  • Power supply DC 12-36V (not included, please feel free to contact us if you need !)
    *This driver get its power from the same unit as the steppers, it doesn't require a separate power source.
    *Voltage Selection:
    12-16V DC power supply for Nema 17 stepper motors
    16-24V DC power supply for Nema 23 stepper motors
    24-36V DC power supply for Nema 34 stepper motors
    (High voltage will burn up the chips or stepper motors!!!)
    *Ampertage Selection:
    Output current of the power supply can be calculated by the following expressions:
    Output current = Rated current of your stepper motors * quantity + 2A

    (For example, if you want to drive 3 * 3A Nema 23 stepper motors, theoretically 24V 11A DC power supply is recommended, but higher power such as 24V 15A also will be good.
    If you are not sure about the selection of power supply, please feel free to contact us for help)
  • The power output of 12V shall be applied to the radiator fan of 12V
  • Driver output compatible with 2 or 4 phase, 4,6 or 8 lead stepper motors, 3A max.
  • Suitable for unipolar or bipolar stepper motors.
  • Voltage regulated spindle speed controlled by parallel interface as function of supply voltage.

Specification of 57BYGH76-401A Motor:

Model

Step angle

Motor length

Rated current

Phase resistance

Phase inductance

Holding torque

Lead wire

Rotor inertia

Weight

Single Shaft

 

°

L(mm)

A

Ω

mH

Oz-in

Kgf.cm

No.

g.cm2

kg

57BYGH76-401A

1.8

76

2.8

1.13

3.6

263

18.9

4

480

1.0

Package include:

  • 1 x 3 Axis TB6560 Stepper Motor Driver 1.5A-3A
  • 5 x Connectors
  • 1 x DB25 parallel cable
  • 1 x CD software(English Manual & Mach3 demo version)
  • 3 x 57BYGH76-401A Stepper motor

Previous: CNC Kit 5 Axis NEMA 23 Stepper Motor 56mm*5+ TB6560 Driver Controller

NextChoken-Bako Robotic Dog Bank Box Hungry Coin Eat 3colors

Customer Images

Reviews
Write a ReviewPost PhotosPost Videos, and get GoodLuckBuy points!
  TB6560 is crap
Posted by Jeffrey Olijar on 08/30/2013, 07:38
Involvement:General (knows how to use it) - Ownership:less than 1 day
Price: ****
Ease of Use: *
Build Quality: *
Usefulness: **
Overall Rating: ***
Pros:Price is good.
Cons:Board is covered in some sort of dust with lots of finger prints... looks like it was left outside.

I can drive the axis with Mach 3 however it is very noisy and It misses tons of steps making the board completely unusable.
Other Thoughts:Paid for UPS shipping and delivery date was off by one week because they didn't ship for a week. whats the point of paying $20 for expatiated shipping if they don't ship within a day or two.. not happy...
Bottomline:I would look elsewhere the quality of the board is well known to be bad... I ordered the board with stepper motors hoping that the board would work but really wanted the motors... all in all 3/5 because the motors I ordered work. going to buy a gecko 540 and not have to worry about crappy control boards.

Discussions

Loading...
122