Categories
CRIUS MAVLink-OSD V2.0 APM Minim OSD Compatible ATMEGA328P Microcontroller DC/DC Voltage Stabilization

Move to view larger images

CRIUS MAVLink-OSD V2.0 APM Minim OSD Compatible ATMEGA328P Microcontroller DC/DC Voltage Stabilization CRIUS MAVLink-OSD V2.0 APM Minim OSD Compatible ATMEGA328P Microcontroller DC/DC Voltage Stabilization

CRIUS MAVLink-OSD V2.0 APM Minim OSD Compatible ATMEGA328P Microcontroller DC/DC Voltage Stabilization CRIUS MAVLink-OSD V2.0 APM Minim OSD Compatible ATMEGA328P Microcontroller DC/DC Voltage Stabilization

CRIUS MAVLink-OSD V2.0 APM Minim OSD Compatible ATMEGA328P Microcontroller DC/DC Voltage Stabilization CRIUS MAVLink-OSD V2.0 APM Minim OSD Compatible ATMEGA328P Microcontroller DC/DC Voltage Stabilization

CRIUS MAVLink-OSD V2.0 APM Minim OSD Compatible ATMEGA328P Microcontroller DC/DC Voltage Stabilization

CRIUS MAVLink-OSD V2.0 APM Minim OSD Compatible ATMEGA328P Microcontroller DC/DC Voltage Stabilization

Price: $8.20
SKU: 102407
0
diggs
Price in points: 82 points
Points: 1 points

US_WC/US_KY/UK_CK1/DE_EK/DE_EDA/DE_CK1 Local stock!!!

Our wholesale prices:

Quantity  5+   20+   50+   100+ 
Price  $8.20   $8.20   $8.20   $8.20 
Description

CRIUS MAVLink-OSD V2.0 MinimOSD Compatible ATMEGA328P Microcontroller DC/DC Voltage Stabilization

Introduction:

- MAVLink-OSD is an Arduino based project and it is fully compatible with original MinimOSD.
- This board can be used for CRIUS AIOP and Arduflyer / ArduPilot-Mega.
- MAVLink-OSD with switching DC/DC stepdown powersupply to maximize efficiency on power system. No more heating problems when using this OSD board.

- Default OSD Firmware is MinimOSD-Extra, written by Gábor Zoltán.
- About how to use the configurator tool to setup OSD function: https://code.google.com/p/minimosd-extra/

- How to setup hardware (original MinimOSD Wiki): https://code.google.com/p/arducam-osd/wiki/How_to_start_minim

Hardware Features:

- ATMEGA328P Microcontroller
- MAX7456-EUI monochrome on-screen display
- 5V/500mA DC/DC regulator for MAX7456-EUI
- Operating voltage: 5V(FTDI connector) and 12V(Video I/O connector)
- Supported NTSC & PAL
- FTDI connector

Software features:
- Full MAVLink protocol support
- Graphical configurator tool

Other

- Dimension: 19mmx39mm(no include 0.1” pith 90°connector)
- Weight: 5g/6g(include cable)

Package Included:
- MAVLink-OSD V2.0 x 1
- UART 4Pin cable 150mm for APM x1
- UART 6Pin cable 150mm for pixhawk x1

Previous: SKY-702 FPV 7inch 800*480 LED Screen Dual 32 Frequency Point Diversity Receive Monitor w/Sunshade

NextDJI DT7 2.4G 7 Channel Remote Controller Transmitter w/DR16 Receiver

Reviews
Write a ReviewPost PhotosPost Videos, and get GoodLuckBuy points!
  FTDI connection issues
Posted by Gabriel Alonso Neto on 01/24/2014, 09:15
Involvement:General (knows how to use it) - Ownership:1 week to 1 month
Price: ****
Ease of Use: **
Build Quality: *****
Usefulness: ***
Overall Rating: ****
Pros:Price and compatibility with Crius all in one FC
Cons:No manual
Other Thoughts:If you are having problems to connect with the OSD Config Tool (Arducan OSD Config) using the FTDI cable, then you have to press the reset button and right after click the desired command in the program (load or write). In my case there was a message saying the program could not communicate with the OSD when using the FTDI cable. I figure out the solution after a long research on the net. It worked well for me.
Bottomline:Recommend but definitely not for new bees.

Discussions

Loading...
122