Categories
new

Move to view larger images

XTC 2 Clip Tool for HTC M8 M9 unlock + Y Cable Repair IMEI/CID/MEID

Price: $123.61
SKU: 127045
0
diggs
Price in points: 1236 points
Points: 12 points
Description

XTC 2 Clip Tool for HTC M8 M9 unlock + Y Cable Repair IMEI/CID/MEID

Supported Models
XTC 2 Clip is supposed to support the whole range of HTC phones, however the features may differ from model to model.

Below is the list of tested models as per 1 May 2015:

New age
- HTC M9
- Butterfly
- Butterfly 2
- Desire 200
- Desire 300
- Desire 400 DualSim
- Desire 500 dualsim
- Desire 510
- Desire 526G+ dualsim
- Desire 600 dualsim
- Desire 601 Dualsim
- Desire 601 singlesim
- Desire 610 singlesim
- Desire 620 Dual
- Desire 700 Dual
- Desire 816 dual sim
- Desire 816 SingleSim
- Desire 816G
- Desire 820
- Desire 820 Dual sim 820u
- Desire 820 mini
- Desire 820s
- Desire 826w
- Desire C
- Desire Eye
- Desire SV
- Desire U dualsim
- Desire V
- Desire X
- Droid Verizon
- E8 SingleSim Sprint
- Nexus 9
- One
- One E8 dual
- One E8 M8Sx Red
- One J (KDDI Japan)
- One M7
- One M8 DualSim
- One M8 SingleSim
- One Max
- One Mini
- One Mini 2
- One Remix Verizon
- One S
- One SV
- One V
- One X
- One XL
- Rider 4G
- Sensation (Pyramid)
- Sensation XL (X315e)
- Vivid

How does it work?
In order to use its functions – you have to connect it to the SD card port of your phone. The SD port may be located on the left, right or rear (battery) part of your phone. If your phone has no SD port – you must use Y-cable.

Operation mode
There are 2 operation mode for XTC 2 Clip device:
- direct – when the phone is in fastboot mode & connected to the PC, using the XTC 2 Clip software

- offline – when using a SIM Lock menu of bootloader. To use the offline mode you must first save special service files on XTC 2 Clip device.

Direct mode
To use direct mode:
- Insert XTC 2 Clip device into phone SD card slot, power on phone into bootloader mode using “vol-down + pwr” button. And select “FASTBOOT” option.

- Connect phone to your PC.

- Run the XTC 2 Clip software and select “Direct mode”.

- Choose the desired operation and press corresponding button.

SIM LOCK FUNCTION IS NOT AVAILABLE IN DIRECT MODE! PLEASE USE OFFLINE MODE FOR SIM LOCK MANAGEMENT.
Important

IF YOU GET A ‘SD CARD NOT FOUND’ MESSAGE – IT MEANS THAT THE XTC 2 CLIP WAS CONNECTED AFTER PHONE WAS POWERED ON. IN THIS CASE PRESS THE ‘REBOOT BOOTLOADER’ BUTTON AND REPEAT THE DESIRED OPERATION.

Offline mode
How to prepare service files on XTC 2 Clip device:
- Connect the XTC 2 Clip device to your PC using any compatible microsd card reader.
- The device will be detected as a flash/disk drive.
- Run the XTC 2 Clip software and select “SD editor” tab.
- If you have previously had your service files on your device, please press “Read from drive” button, otherwise you will lose all your existing files once used the “Save to drive”.
- Select the options you need and press “Save to drive”
- Insert XTC 2 Clip device into phone SD card slot, power on phone into bootloader mode using “vol-down + pwr” button and select “SIMLOCK” option.
Important

THE SIM LOCK SETTINGS ARE BOUND TO THE PHONE’S IMEI. IN OTHER WORDS, IF YOU NEED TO LOCK/UNLOCK A PHONE, YOU MUST ADD PHONE’S IMEI TO SPECIAL ‘CONFIG.DAT’ FILE USING THE ‘SD EDITOR’ TAB.

OTHERWISE YOU WILL GET ‘IMEI CHECKING FAIL’ AND YOUR PHONE WILL NOT BE UNLOCKED/LOCKED! CID, IMEI, SECURITY FLAG SETTINGS ARE NOT BOUND, YOU CAN USE IT ON AS MANY PHONES AS YOU WISH WITHOUT HAVING TO CONNECT THE DEVICE TO PC EACH TIME.
 
Offline mode – manual files creation
It may happen that you need to create service files on a PC with no XTC 2 Clip software installed. In this case you can manually create the files for:
- IMEI change/repair – imei.txt
- Security level change – sf.txt
- CID change – cid.txt

Please note, that unlike mentioned files, SIM lock configuration ‘config.dat’ is a binary file, and you may need to use a hex editor to create it. Therefore it’s recommended that you use an XTC 2 Clip software to create/manage this file.

TO CREATE/MODIFY THE FILES YOU CAN USE SIMPLE ‘NOTEPAD’ SOFTWARE

IMEI file
To modify the phone’s IMEI you need to create a text file called ‘imei.txt’ in the root folder of a XTC 2 Clipdevice disk drive. Once created, put inside a 14 digits of a new IMEI, for example: 12345678901234

SF file
To modify the phone’s security level (S-ON/S-OFF) you need to create a text file called ‘sf.txt’ in the root folder of a XTC 2 Clip device disk drive. Once created, put inside a number that corresponds to the desire security level:

- 0 means security OFF (S-OFF)
- 1 means (S-ON level 1)
- 2 means (S-ON level 2)
- 3 means (S-ON level 3, highest)

CID file
To modify the phone’s CID you need to create a text file called ‘cid.txt’ in the root folder of a XTC 2 Clip device disk drive. Once created, put inside a 8 symbols of a new CID, for example: HTC__001

Previous: BST Dongle Servicing Device for HTC and Samsung Android Smartphones

NextYHT100 Portable Rebound Leeb Hardness Tester Meter

Reviews
Write a ReviewPost PhotosPost Videos, and get GoodLuckBuy points!


No posts found
 

Discussions

Loading...
122