12-36V 3A TB6560 3 Axis CNC Motor Driver Stepper NEW

Move to view larger images

12-36V 3A TB6560 3 Axis CNC Motor Driver Stepper NEW 12-36V 3A TB6560 3 Axis CNC Motor Driver Stepper NEW

12-36V 3A TB6560 3 Axis CNC Motor Driver Stepper NEW 12-36V 3A TB6560 3 Axis CNC Motor Driver Stepper NEW

12-36V 3A TB6560 3 Axis CNC Motor Driver Stepper NEW

3A TB6560 3 Axis CNC Motor Driver Stepper 12V-36V

Price: $42.62
SKU: 59368
Price in points: 426 points
Points: 4 points

Our wholesale prices:

Quantity  5+   20+   50+   100+ 
Price  $42.62   $42.62   $42.62   $42.62 


  • Toshiba TB6560AHQ chip - High power, maximum 3.5A drive current chipset !
    For TB6560AHQ Datasheet, Please click here.
  • 1-1/16 microstep setting - Higher accuracy and smoother operation than standard 1, 1/2 step!
  • Adjustable 1.5A-3A drive current settings for each axis - 25%,50%,75%,100% of full current can be set for different stepper motors
    *Attention: This driver is the 1.5A-3A version, it's specially designed for stepper motors with rated current from 1.5A to 3A, it's NOT compatible with stepper motors with rated current below 1.5A or above 3A!
    If the rated current your stepper motors is below 1.5A, you can choose the 0.5A-2.5A version!
    Please let us know which version (1.5A-3A version is default) you need immediately after placing a bid!
  • Overload, over-current and over-temperature safety - Full protection for your computer and peripheral equipment !
  • On board current switching - Power output can be set according to specific user requirement !
  • Full closed-type optical isolation to protect the user's computer and equipment
  • Relay spindle interface - Outputs Max. 36V 7.5A for spindle motors or coolant pump (only one device can be powered by this output!)
  • 4 channel inputs interface- Can be used for XYZ limit and emergency stop !
  • Professional design - Two stage signal processing with super anti-jamming !
  • Bipolar constant current chopper drive with non-resonant region - Controls motors smoothly through range without creep effect !
  • Four control inputs (divided into pairs of knives) - Allows setting of limit and emergency stop !
  • Universal architecture - Supports most parallel software MACH3,KCAM4 etc!
    *For compatibility with other softwares, please feel free to contact us!



Electrical properties (ambient temperature Tj = 25 ℃ pm):
Input Power 12-36V DC power supply
Stepper motor drive current 1.5A - 3A/phase
Drive type Double-pole constant flow PWM actuation output
Compatible Stepper motors 2 or 4 phase, 4,6 or 8 lead stepper motors, 3A max.
Dimensions 18 * 14 * 4 cm (L*W*H)

Dip settings:

Current Setting 1 2 Decay Mode Settings 3 4 MicroStep Settings 5 6
75% ON OFF 25% ON OFF 1/2 ON OFF
50% OFF ON 50% OFF ON 1/8 OFF ON

Further Details:
  • Power supply DC 12-36V (not included, please feel free to contact us if you need !)
    *This driver get its power from the same unit as the steppers, it doesn't require a separate power source.

    *Voltage Selection:
    12-16V DC power supply for Nema 17 stepper motors
    16-24V DC power supply for Nema 23 stepper motors
    24-36V DC power supply for Nema 34 stepper motors
    (High voltage will burn up the chips or stepper motors!!!)
    *Ampertage Selection:
    Output current of the power supply can be calculated by the following expressions:
    Output current = Rated current of your stepper motors * quantity + 2A
    (For example, if you want to drive 3 * 3A Nema 23 stepper motors, theoretically 24V 11A DC power supply is recommended, but higher power such as 24V 15A also will be good.
    If you are not sure about the selection of power supply, please feel free to contact us for help)
  • The power output of 12V shall be applied to the radiator fan of 12V
  • Driver output compatible with 2 or 4 phase, 4,6 or 8 lead stepper motors, 3A max.
  • Suitable for unipolar or bipolar stepper motors.
  • Voltage regulated spindle speed controlled by parallel interface as function of supply voltage.

Package include:

  • 1 x 3 Axis TB6560 Stepper Motor Driver 1.5A-3A
  • 5 x Wire connectors
  • 1 x DB25 parallel cable
  • 1 x CD software(English Manual & Mach3 demo version)

Tags:  3 Axis Motor Driver   3 Axis CNC Driver   3 Axis CNC Motor Driver Board  

Previous: 4 Axis TB6560 Driver for NEMA 17/23/34 CNC Stepper Motor Engraving Machine

NextGPS Sports Recorder (BT-1300S)-White Green

Write a ReviewPost PhotosPost Videos, and get GoodLuckBuy points!
Posted by Andrew Aleksandrovich Ozornin on 05/13/2011, 20:51
Involvement:General (knows how to use it) - Ownership:more than 1 month
Price: *****
Ease of Use: ****
Build Quality: *****
Usefulness: *****
Overall Rating: *****
Pros:Made qualitatively. Simply connected.
Cons:Not immediately clear designation switches.
Other Thoughts:Buy a power supply.
Bottomline:Very not bad.