Categories

Move to view larger images

HMBGC Micro Brushless Gimbal Controller Driver w/Sensor Alexmos upgradeable firmware

Price: $17.21
SKU: 102403
0
diggs
Price in points: 172 points
Points: 2 points
Out Of Stock

Our wholesale prices:

Quantity  5+   20+   50+   100+ 
Price  $17.21   $17.21   $17.21   $17.21 
Description

HMBGC Micro Brushless Gimbal Controller Driver w/Sensor Alexmos upgradeable Firmware

Features:

- Compatible with Alexmos2.2 or firmware below, compatible with newest German BruGi_050 firmware, default Russian2.2 firmware
- preload Alexmos 8bit upgradeable Firmware
- SMT production, stable quality
- MOS tube instead of L6234D to drive motors
- Peak current 10A
- Work current: 5A(suggest heat sink)
- Reserve IIC port, directly connect with development board, no need jump wire

we recommend using 12V BEC POWER SUPPLY

we

Previous: HJ-6504 Carbon Fiber Folding Four-axis Quadcopter Aircraft Frame Kit

NextDJI Phantom 2 Vision Quadcopter Part 5 CCW Brushless Motor with White Prop Cap

Reviews
Write a ReviewPost PhotosPost Videos, and get GoodLuckBuy points!
  ONLY USE 2S 7,4-8,4V
Posted by hththth on 9/15/2014, 16:51
Involvement:Expert (understands the inner workings) - Ownership:more than 1 month
Price: *****
Ease of Use: *****
Build Quality: *****
Usefulness: *****
Overall Rating: *****
Pros:If you use 12V you destroy the board!!!!!!
only use 2S 7,4-8,4V than you will have some fun with this board!
Cons:If you use 12V you destroy the board!!!!!!
only use 2S 7,4-8,4V than you will have some fun with this board!
Other Thoughts:If you use 12V you destroy the board!!!!!!
only use 2S 7,4-8,4V than you will have some fun with this board!
Bottomline:If you use 12V you destroy the board!!!!!!
only use 2S 7,4-8,4V than you will have some fun with this board!
  HMBGC
Posted by lukas schwichtenberg on 07/07/2014, 21:01
Involvement:Expert (understands the inner workings) - Ownership:less than 1 day
Price: *
Ease of Use: *
Build Quality: *
Usefulness: *
Overall Rating: *
Pros:buyed 4 off these. the first one runs with brugi 050 very well but after the third fly nothing works no more! the other three died after ten minutes of working. buy anything else but not these fuc.ing shi...
Cons:buyed 4 off these. the first one runs with brugi 050 very well but after the third fly nothing works no more! the other three died after ten minutes of working. buy anything else but not these fuc.ing shi...
Other Thoughts:buyed 4 off these. the first one runs with brugi 050 very well but after the third fly nothing works no more! the other three died after ten minutes of working. buy anything else but not these fuc.ing shi...
Bottomline:buyed 4 off these. the first one runs with brugi 050 very well but after the third fly nothing works no more! the other three died after ten minutes of working. buy anything else but not these fuc.ing shi...
  works well
Posted by ronald mallett on 06/15/2014, 04:16
Involvement:General (knows how to use it) - Ownership:more than 1 month
Price: *****
Ease of Use: ****
Build Quality: ****
Usefulness: ****
Overall Rating: ****
Pros:Works well (unlike some other companiesthat sell with a gimbal), very small, works off 2s (7.4v). not tried on gimbal yet but connect to GUI easy
Cons:No documentation, uses simpleBGC 2.2.b2 GUI. dont know about updated firmware, but may be possible. no wires with it, but u can buy silicon wire from here
Other Thoughts:documentation need, also links to GUI and firmware. gimbal this would fit on would be nice. sample settings for a gopro would be nice
Bottomline:Cheap, works, can be setup (unlike some others), dont use more then 7.4v
  Dead in 10 minutes
Posted by Maksim Kollegov on 03/22/2014, 14:35
Involvement:Expert (understands the inner workings) - Ownership:less than 1 day
Price: *****
Ease of Use: *****
Build Quality: **
Usefulness: ***
Overall Rating: *
Pros:Small, ligtweight easy to config..onboard connectors are not soldered... that's good, you can solder direct or install stright or angle connectors as you like...

Cons:Tested it with HD16 boscam camera and gimbal with 2804 gimbal motors. with 12v power at 70%PWM and dies after a 10 min of use. First dead halfbridge cascade blows up of atmega.. Pooh.. and fried....No protection from overheat or overcurrent.
Second... missing cable and connectors for imu board..you need to DIY.
Other Thoughts:probably can be used for smaller motors like 22xx with higher impedance... but not with 10ohm motors...
Bottomline:Do not recommend for more then gopro size camera and larger motors.... And do not set PEM more then 50% on 12V ... with typical 10-12ohm brashless motor impedanse mosfets will fry.
  Bought for backup at good price.
Posted by Theuer Weirich on 03/22/2014, 02:37
Involvement:Expert (understands the inner workings) - Ownership:1 day to 1 week
Price: *****
Ease of Use: *****
Build Quality: *
Usefulness: *
Overall Rating: *
Pros: Nice PCB, easy to solder wires and pins.
Cons: The controller worked ONLY for 2 or 3 minutes without any motor plugged.
I turned on the controller, plugged the USB and connected with PC. Everything was fine, when suddenly the 2 MOS exploded!
Now the controller turn on the red led, but don't do anything more.
Other Thoughts: I was excited about the purchase, but it was a bad deal.
Bottomline:.

Discussions

Loading...
122